|
31:
|
Paging Matt Hawkins
(Archive: GFC - by DreXteR, started: 02-21-2003, last post: 2003-05-31 10:15:25 CEST)
Matt, I need to contact Steve Hamm from custom speed. Can you provide me some emial or tel?ThanxDreX
Score: 1000, Size: 29 bytes
|
32:
|
3.4l DOHC Turbo Finally Alive
(Archive: TD&Q - by Matt Hawkins, started: 10-01-2002, last post: 2003-05-31 09:52:03 CEST)
I finally got my Turbo 3.4l TDC project running. I am using a T3 turbo specially machined for a T4 compressor wheel. The intercooler is from an SVO Mustang with the inlet moved for better fit. Engine management is being done with a Haltech E6K. The intake is custom made with a carbon fiber top...
Score: 1000, Size: 44 bytes
|
33:
|
Torsen LSD Intall Advice
(Archive: TD&Q - by Matt Hawkins, started: 10-07-2002, last post: 2003-02-04 11:37:35 CET)
I lucked upon a Torsen LSD from a FWD Olds. I have read all of the horror stories from people who have used them and broken them in Fiero transmissions. I think I know why the failures are occuring and how they can be prevented. This LSD has a pretty high torque bias. This allows for a...
Score: 1000, Size: 39 bytes
|
34:
|
First broken CV with 3.4l DOHC Turbo
(Archive: TD&Q - by Matt Hawkins, started: 10-10-2002, last post: 2003-02-04 11:37:33 CET)
I bought a replacement left side axle for the Fiero on Monday night and installed it in the car. Drove the car Tuesday night and then to work on Wed. After work I was doing some work to the car with a friend and took him for a ride when we were done. I did two agressive launches and on the...
Score: 1000, Size: 51 bytes
|
35:
|
1/4 Mile Time For DOHC Turbo
(Archive: TD&Q - by Matt Hawkins, started: 10-24-2002, last post: 2003-02-04 11:36:58 CET)
Well, I just got back from Milan Dragway. I ran two 13.7 second runs at a little over 100 MPH. This was with about 7 psi of boost and crazy rich mixtures. Also, my 60 foot times were only in the 2.0x second range. With more tuning and a better launch, I hope for low 13s with 7 psi of boost. ...
Score: 1000, Size: 43 bytes
|
36:
|
How ABS Works - Very Long
(Archive: TD&Q - by Matt Hawkins, started: 10-26-2002, last post: 2003-02-04 11:36:51 CET)
ABS BrakesBy Steve Sancricca, ABS Application Engineer, Robert Bosch CorporationThe intent of this article is to explain the basic operating principles of anti-lock braking systems (ABS), discuss the system components, and relate performance of the system to some basic vehicle dynamics principles. ...
Score: 1000, Size: 40 bytes
|
37:
|
FWD Getrag VSS output?
(Archive: TD&Q - by Matt Hawkins, started: 05-06-2002, last post: 2002-08-25 11:44:48 CEST)
What is the output of the FWD VSS? I know the Fiero is 4000 pulses per mile. Thanks.Matt86 GT, 5-spd87 GT, 5-spd DOHC Turbo, Haltech - In progress
Score: 1000, Size: 37 bytes
|
38:
|
3.4l DOHC coolant plumbing question
(Archive: TD&Q - by Matt Hawkins, started: 04-28-2002, last post: 2002-08-25 11:44:19 CEST)
For those of you who have completed the DOHC swap, how did you plumb the coolant lines? Both the heater core and radiator. Thanks.Matt86 GT, 5-spd87 GT, 5-spd DOHC Turbo - in progress
Score: 1000, Size: 50 bytes
|
39:
|
5-spd FWD Getrag question
(Archive: TD&Q - by Matt Hawkins, started: 04-30-2002, last post: 2002-08-25 11:44:19 CEST)
What is the output of the FWD VSS? I have to use the FWD sensor because I am using a Torsen LSD which has the tone ring machined into the housing. I can't use the Fiero ring and I need to know the difference so I can make a convertor box to run the speedo. Thanks.Matt86 GT, 5-spd87 GT, 5-spd...
Score: 1000, Size: 40 bytes
|
40:
|
Anyone have aluminum cradle bushing dimesions?
(Archive: TD&Q - by Matt Hawkins, started: 04-14-2002, last post: 2002-08-25 11:44:03 CEST)
I am looking for the dimensions needed to fabricate aluminum cradle bushings. Thanks.Matt86 GT87 GT
Score: 1000, Size: 61 bytes
|
| |
|